Toyota Venza: Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

Toyota Venza Service Manual / Window / Glass / Power Window Control System / Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch

DESCRIPTION

If the manual up/down function can be performed but the auto up/down function cannot, then the fail-safe mode may be functioning.

If the power window initialization (See page ) has not been performed, the auto up/down function
will not operate.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

The power window control system uses a multiplex communication system (LIN communication system). Inspect the communication function by following How to Proceed with Troubleshooting (See page ). Troubleshoot the power window control
system after confirming that the communication system is functioning properly.
When the power window regulator motor assembly (for driver side) is reinstalled or replaced, the power window control system must be initialized.
After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
1. Close the power window by fully pulling up the power window regulator master switch assembly and holding it at the auto up position.
2. Open the power window by fully pushing down the power window regulator master switch assembly.
When the ECU determines that the power window regulator motor assembly (for driver side) has a malfunction, DTC B2311 is set.

PROCEDURE

1.	READ VALUE USING TECHSTREAM (Master Switch)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Master switch / Data List.

(e) Read the Data List according to the display on the Techstream.

Master Switch (Power Window Regulator Master Switch Assembly)

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door P/W Auto SW	Driver side power window auto up/down switch signal / ON or OFF	ON: Driver side power window auto switch operated OFF: Driver side power window auto switch not operated	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Auto SW

Driver side power window auto up/down switch signal / ON or OFF

ON: Driver side power window auto switch operated

OFF: Driver side power window auto switch not operated

OK:

On the Techstream screen, ON or OFF is displayed accordingly.

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

2.	READ VALUE USING TECHSTREAM (D-Door Motor)

(a) Enter the following menus: Body Electrical / D-Door Motor / Data List.

(b) Read the Data List according to the display on the Techstream.

D-Door Motor (Power Window Regulator Motor Assembly (for Driver Side))

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
D Door P/W Auto SW	Driver side power window auto up/down switch signal / ON or OFF	ON: Driver side power window auto switch operated OFF: Driver side power window auto switch not operated	-

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door P/W Auto SW

Driver side power window auto up/down switch signal / ON or OFF

ON: Driver side power window auto switch operated

OFF: Driver side power window auto switch not operated

OK:

On the Techstream screen, ON or OFF is displayed accordingly.

GO TO STEP 5

3.	PERFORM INITIALIZATION (for Driver Side)

(a) Initialize the power window regulator motor assembly (for driver side) (See page ).

4.	CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)

(a) Check that the driver side door power window moves when the auto up/down function of the power window regulator master switch assembly is operated (See page ).

OK:

Driver side auto up/down function is normal.

END (PROBLEM DUE TO INITIALIZATION FAILURE)

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

5.	REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

(a) Replace the power window regulator master switch assembly (See page ).

6.	CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION)

(a) Check that the driver side door power window moves when the auto up/down function of the power window regulator master switch assembly is operated (See page ).

OK:

Driver side auto up/down function is normal.

END (POWER WINDOW REGULATOR MASTER SWITCH WAS DEFECTIVE)

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side)

Rear Power Window RH does not Operate with Rear Power Window Switch RH

DESCRIPTION When the engine is running or the ignition switch is ON, the power window regulator motor assembly (for rear RH side) is operated by the power window regulator switch assembly (for re ...

Front Passenger Side Power Window Auto Up / Down Function does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION If the manual up/down function can be performed but the auto up/down function cannot, the fail-safe mode may be functioning. If the power window initialization (See page ) has not be ...

Other materials about Toyota Venza:

Capacity and distribution
Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) — (Total weight of occupants) Steps for Determining Correct Load Limit— (1) Locate the statement “The combined weight of occupants and cargo should ...

Knock Sensor
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE INTAKE MANIFOLD (a) Remove the intake manifold (See page ). 2. REMOVE KNOCK SENSOR (a) Disconnect the sensor connector. ...

Removal
REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the LH side and RH side. The following procedure listed is for the LH side. PROCEDURE 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID NOTICE: If brake fluid leaks onto any pai ...