DISPOSAL
CAUTION / NOTICE / HINT
CAUTION:
Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.
HINT:
When scrapping vehicles equipped with a seat belt pretensioner or disposing of a front seat outer belt (with a seat belt pretensioner), always deploy the seat belt pretensioner first in accordance with the procedure described below. If any abnormality occurs during deployment of the seat belt pretensioner, contact the SERVICE DEPARTMENT of TOYOTA MOTOR SALES, U.S.A., INC.
PROCEDURE
1. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN INSTALLED IN VEHICLE)
NOTICE:
(a) Check the function of SST.
SST: 09082-00700
CAUTION:
When deploying the seat belt pretensioner, always use the specified SST.
(1) Connect the red clip of SST to a battery positive (+) terminal and the black clip to a battery negative (-) terminal. HINT: At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in later step. |
|
(2) Press the SST deployment switch and check that the LED of the SST deployment switch illuminates. CAUTION: If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST. |
|
(b) Connect SST.
(1) Connect 2 SST, and then connect them to the front seat outer belt pretensioner.
SST: 09082-00700
SST: 09082-00770
NOTICE:
To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.
(2) Move SST at least 10 m (33 ft.) away from the front of the vehicle. |
|
(3) Close all the doors and windows of the vehicle.
NOTICE:
Do not damage the SST wire harness.
(c) Deploy the front seat outer belt pretensioner.
(1) Confirm that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.
(2) Connect the red clip of SST to a battery positive (+) terminal and the black clip to a negative (-) terminal.
(3) Press the SST deployment switch to deploy the front seat outer belt pretensioner.
HINT:
The seat belt pretensioner will deploy at the same time as SST LED illuminates.
(d) Dispose of the front seat outer belt assembly. (1) Remove the front seat outer belt assembly and SST. (2) Dispose of the front seat outer belt assembly in accordance with local regulations. CAUTION:
HINT: When scrapping the vehicle, deploy the front seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed. |
|
2. DISPOSE OF FRONT SEAT OUTER BELT ASSEMBLY (WHEN NOT INSTALLED IN VEHICLE)
NOTICE:
(a) Check the function of SST.
SST: 09082-00700
CAUTION:
When deploying the seat belt pretensioner, always use the specified SST.
(1) Connect the red clip of SST to a battery positive (+) terminal and the black clip to a battery negative (-) terminal. HINT: At this time, do not connect the yellow connector. It will be connected to the seat belt pretensioner in later step. |
|
(2) Press the SST deployment switch and check that the LED of the SST deployment switch illuminates. CAUTION: If the LED is illuminated when the deployment switch is not pressed, SST may be malfunctioning. In this case, do not use the malfunctioning SST. |
|
(b) Connect SST.
(1) Connect 2 SST, and then connect them to the front seat outer belt pretensioner.
SST: 09082-00700
SST: 09082-00770
NOTICE:
To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the pretensioner connector.
(2) Place the outer belt on the ground and cover it with a tire and wheel assembly. NOTICE: Position the front seat outer belt assembly as shown in the illustration. |
|
(3) Position and hold SST at least 10 m (33 ft.) away from the wheel.
NOTICE:
Do not damage the SST wire harness.
(c) Deploy the front seat outer belt pretensioner. (1) Check that no one is within a 10 m (33 ft.) radius of the wheel. (2) Connect the red clip of SST to a battery positive (+) terminal and the black clip to a battery negative (-) terminal. (3) Press the SST deployment switch to deploy the front seat outer belt pretensioner. HINT: The seat belt pretensioner will deploy at the same time as SST LED illuminates. |
|
(d) Dispose of the front seat outer belt assembly. (1) Remove the wheel and SST. (2) Dispose of the front seat outer belt assembly in accordance with local regulations. CAUTION:
HINT: When scrapping the vehicle, deploy the front seat outer belt pretensioners, and then scrap the vehicle with the deployed outer belt installed. |
|
Control Module Communication Bus OFF (U0073/86,U0100/85,U0129/83)
DESCRIPTION
The AWD control ECU inputs the signals sent from the ECM and skid control
ECU via the CAN communication system.
When DTCs indicating a CAN communication system malfunction are output,
repair the CAN communication system before r ...
Floor mats
Use only floor mats designed specifically for vehicles of the same model and
model year as your vehicle. Fix them securely in place onto the carpet.
Insert the retaining hooks (clips) into the floor mat eyelets.
Turn the upper knob of each retaining ho ...
AV Signal Stoppage (Low Battery Voltage) (B158F)
DESCRIPTION
This DTC is stored when a video or audio signal is interrupted due to battery
voltage input to the navigation receiver assembly dropping temporarily.
DTC No.
DTC Detection Condition
Trouble Area
...