Toyota Venza manuals

Toyota Venza: Differential Mount Cushion

Toyota Venza Service Manual / Axle And Differential / Differential Mount Cushion

Components

COMPONENTS

ILLUSTRATION


Installation

INSTALLATION

PROCEDURE

1. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

(a) Using SST, install a new rear No. 1 differential mount cushion.

Text in Illustration

*1

Protrusion

-

-

SST: 09570-24011

(A):

5.0 to 6.0 mm (0.197 to 0.236 in.)

(B):

+/- 3°

NOTICE:

  • Install the rear No. 1 differential mount cushion so that the protrusion is positioned upward.
  • Install the rear No. 1 differential mount cushion within +/- 3° from the center.
  • Temporarily install the rear No. 1 differential mount cushion to the rear suspension member before installing SST to prevent the rear No. 1 differential mount cushion from being tilted.
  • Apply grease to the threads of the SST bolts before use.
  • Be sure to use SST in the correct combination.
  • Do not set SST in the wrong direction.
  • Make sure that SST contacts the entire rear No. 1 differential mount cushion seating surface.
  • Do not slant the SST bolts.
  • Tighten the 2 SST bolts equally into the 2 rear No. 1 differential mount cushion holes.

2. INSTALL REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

(a) Using SST, install a new rear No. 2 differential mount cushion.


SST: 09570-24011

(A):

5.0 to 6.0 mm (0.197 to 0.236 in.)

(B):

+/- 3°

NOTICE:

  • Install the rear No. 2 differential mount cushion within +/- 3° from the center.
  • Temporarily install the rear No. 2 differential mount cushion to the rear suspension member before installing SST to prevent the rear No. 2 differential mount cushion from being tilted.
  • Apply grease to the threads of the SST bolts before use.
  • Be sure to use SST in the correct combination.
  • Do not set SST in the wrong direction.
  • Make sure that SST contacts the entire rear No. 2 differential mount cushion seating surface.
  • Do not slant the SST bolts.

3. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

HINT:

Refer to the procedure from Install Rear Differential Carrier Assembly with Differential Support (See page ).


Removal

REMOVAL

PROCEDURE

1. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DIFFERENTIAL SUPPORT

HINT:

Refer to the procedure up to Remove Rear Differential Carrier Assembly with Differential Support (See page ).


2. REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

(a) Using SST, remove the rear No. 1 differential mount cushion.


SST: 09316-12010

SST: 09570-24011

NOTICE:

  • Do not bring SST into contact with the rear suspension member.
  • Do not slant the SST bolts.
  • Do not set SST in the wrong direction.
  • Tighten the 2 SST bolts equally into the 2 rear No. 1 differential mount cushion holes.

3. REMOVE REAR NO. 2 DIFFERENTIAL MOUNT CUSHION

(a) Using SST, remove the rear No. 2 differential mount cushion.


SST: 09316-12010

SST: 09570-24011

NOTICE:

  • Do not bring SST into contact with the rear suspension member.
  • Do not slant the SST bolts.
  • Do not set SST in the wrong direction.
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order ...

Differential Oil
Replacement REPLACEMENT CAUTION / NOTICE / HINT HINT: Stop the vehicle on a level surface. PROCEDURE 1. DRAIN DIFFERENTIAL OIL (a) Using a 10 mm hexagon wrench, remove the rear dif ...

Other materials about Toyota Venza:

Engine Switch Illumination Circuit
DESCRIPTION The illuminated entry system controls the engine switch illumination. WIRING DIAGRAM PROCEDURE 1. PERFORM ACTIVE TEST USING TECHSTREAM (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to O ...

Throttle Actuator Control System - Stuck Open (P2111,P2112)
DESCRIPTION The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body. The throttle positio ...

Lost Communication with AFS ECU (U0182)
DESCRIPTION DTC No. DTC Detection Condition Trouble Area U0182 No communication from the AFS ECU continues. AFS ECU branch wire or connector Power source circuit of AFS E ...

© 2016-2024 Copyright www.tovenza.com

0.1677