DIAGNOSTIC TROUBLE CODE CHART
HINT:
If a trouble code is displayed during the DTC check, inspect the trouble areas listed for that code. For details of the code, refer to the "See page" below.
Power Steering System
DTC Code |
Detection Item |
Trouble Area |
Return-to-normal Condition |
P/S Warning Light |
See page |
---|---|---|---|---|---|
C1511 |
Torque Sensor Circuit Malfunction |
1. Steering column assembly (torque sensor) 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1512 |
Torque Sensor Circuit Malfunction |
1. Steering column assembly (torque sensor) 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1513 |
Torque Sensor Circuit Malfunction |
1. Steering column assembly (torque sensor) 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1514 |
Torque Sensor Power Supply Abnormal |
1. Steering column assembly (torque sensor) 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1515 |
Torque Sensor Zero Point Adjustment Undone |
- |
Zero point calibration occurs |
*1 |
|
C1516 |
Torque Sensor Zero Point Adjustment Incomplete |
- |
Clear DTC |
*1 |
|
C1517 |
Torque Hold Abnormal |
1. Steering column assembly (torque sensor) 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1521 |
Motor Circuit Malfunction |
Power steering ECU |
Ignition switch ON again |
*1 |
|
C1522 |
Motor Circuit Malfunction |
1. Steering column assembly 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1523 |
Motor Circuit Malfunction |
1. Steering column assembly 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1524 |
Motor Circuit Malfunction |
1. Steering column assembly 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1525 |
Rotation Angle Sensor Initialization Undone |
- |
Rotation angle sensor calibration occurs |
*1 |
|
C1526 |
Rotation Angle Sensor Initialization Incomplete |
- |
Clear DTC |
*1 |
|
C1528 |
Motor Rotation Angle Sensor Malfunction |
1. Steering column assembly (built into steering column assembly) 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1531 |
ECU Malfunction |
Power steering ECU |
Ignition switch ON again |
*1 |
|
C1532 |
ECU Malfunction |
Power steering ECU |
Ignition switch ON again |
*1 |
|
C1533 |
ECU Malfunction |
Power steering ECU |
After normal judgment |
*2 |
|
C1534 |
ECU Malfunction |
Power steering ECU |
Ignition switch ON again |
*2 |
|
C1541 |
Vehicle Speed Signal Malfunction |
1. Speed sensor circuit 2. Brake actuator assembly (Skid control ECU) 3. CAN communication system 4. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1551 |
IG Power Supply Voltage Malfunction |
1. ECU-IG No. 2 fuse 2. IG power source circuit 3. Power steering ECU |
Ignition switch ON again or after normal confirmation |
*1 |
|
C1552 |
PIG Power Supply Voltage Malfunction |
1. PIG power source circuit 2. Power steering ECU |
Ignition switch ON again or after normal confirmation |
*1 |
|
C1554 |
Power Supply Relay Failure |
Power steering ECU |
Ignition switch ON again |
*1 |
|
C1555 |
Motor Relay Welding Failure |
1. Steering column assembly 2. Power steering ECU |
Ignition switch ON again |
*1 |
|
C1581 |
Assist Map Number Un-Writing |
1. Power steering ECU 2. CAN communication system 3. ECM 4. Brake actuator assembly (Skid control ECU) |
Assist map whitten |
*1 |
|
C1582 |
Assist Map Number Mismatch |
1. Power steering ECU 2. CAN communication system 3. ECM 4. Brake actuator assembly (Skid control ECU) |
After normal condition |
*2 |
|
U0100 |
Lost Communication with ECM / PCM "A" |
1. CAN communication system 2. ECM |
After normal condition |
*3 |
|
U0129 |
Lost Communication with Brake System Control Module |
1. CAN communication system 2. Brake actuator assembly (Skid control ECU) |
After normal condition |
*1 |
|
Installation
INSTALLATION
PROCEDURE
1. INSTALL HEADLIGHT ASSEMBLY
(a) Connect each connector.
(b) Install the headlight assembly with the bolt and 3 screws.
Torque:
3.6 N·m {37 kgf·cm, 32 in·lbf}
2. INSTALL FRONT BUMPER ASSEMBLY
(See page )
3. CONNECT CABLE T ...
Removal
REMOVAL
PROCEDURE
1. REMOVE FRONT SEAT HEADREST ASSEMBLY
2. REMOVE FRONT SEAT REAR OUTER TRACK COVER
3. REMOVE FRONT SEAT REAR INNER TRACK COVER
4. REMOVE FRONT SEAT ASSEMBLY
5. REMOVE RECLINING POWER SEAT SWITCH KNOB
6. REMOVE SLIDE AND VER ...
Test Mode Procedure
TEST MODE PROCEDURE
1. WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK
(a) Release the parking brake.
NOTICE:
Before releasing the parking brake, move the shift lever to P for safety.
HINT:
When the parking brake is applied or the brake fluid level is lo ...