DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / Occupant Detection / Data List.
(f) Check the values by referring to the table below.
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
IG Switch |
Ignition switch condition/ ON: Ignition switch ON OFF: Ignition switch off |
ON/OFF |
- |
Passenger Buckle SW |
Passenger side buckle switch/ Set: The seat belt is fastened Unset: The seat belt is not fastened NG: Data is not determined |
Set/Unset |
- |
Passenger Classification |
Passenger classification/ AM50: Adult (more than 54 kg (119.1 lb)) is seated AF05: Adult (36 to 54 kg (79.4 to 119.1 lb)) is seated Child: Child (less than 32 kg (70.6 lb)) is seated CRS: Child restraint system (less than 32 kg (70.6 lb)) and passenger side buckle switch is on OFF: Vacant |
AM50/AF05/Child/CRS/OFF |
- |
Sensor Range Info |
Sensor range information/ OK: The value of a sensor is within the range NG: The value of a sensor is over the range |
OK |
- |
FL Sensor Range Info |
Front left sensor range information/ OK: Sensor range is -17 to 27 kg (-37.5 to 59.5 lb) Min.: Less than -17 kg (-37.5 lb) Max.: More than 27 kg (59.5 lb) |
OK |
- |
FR Sensor Range Info |
Front right sensor range information/ OK: Sensor range is -17 to 27 kg (-37.5 to 59.5 lb) Min.: Less than -17 kg (-37.5 lb) Max.: More than 27 kg (59.5 lb) |
OK |
- |
RL Sensor Range Info |
Rear left sensor range information/ OK: Sensor range is -17 to 37 kg (-37.5 to 81.6 lb) Min.: Less than -17 kg (-37.5 lb) Max.: More than 37 kg (81.6 lb) |
OK |
- |
RR Sensor Range Info |
Rear right sensor range information/ OK: Sensor range is -17 to 37 kg (-37.5 to 81.6 lb) Min.: Less than -17 kg (-37.5 lb) Max.: More than 37 kg (81.6 lb) |
OK |
- |
FL Sensor Voltage |
Front left sensor voltage/ Min.: 0 V Max.: 5 V |
0 to 5 V |
- |
FR Sensor Voltage |
Front right sensor voltage/ Min.: 0 V Max.: 5 V |
0 to 5 V |
- |
RL Sensor Voltage |
Rear left sensor voltage/ Min.: 0 V Max.: 5 V |
0 to 5 V |
- |
RR Sensor Voltage |
Rear right sensor voltage/ Min.: 0 V Max.: 5 V |
0 to 5 V |
- |
FL Sensor Weight Info |
Front left sensor weight information/ Min.: -17 kg (-37.5 lb) Max.: 27 kg (59.5 lb) |
-17 to 27 kg (-37.5 to 59.5 lb) |
- |
FR Sensor Weight Info |
Front right sensor weight information/ Min.: -17 kg (-37.5 lb) Max.: 27 kg (59.5 lb) |
-17 to 27 kg (-37.48 to 59.52 lb) |
- |
RL Sensor Weight Info |
Rear left sensor weight information/ Min.: -17 kg (-37.5 lb) Max.: 37 kg (81.6 lb) |
-17 to 37 kg (-37.5 to 81.6 lb) |
- |
RR Sensor Weight Info |
Rear right sensor weight information/ Min.: -17 kg (-37.5 lb) Max.: 37 kg (81.6 lb) |
-17 to 37 kg (-37.5 to 81.6 lb) |
- |
Total Weight Information |
Total weight information/ Min.: -68 kg (-149.9 lb) Max.: 128 kg (282.2 lb) |
-68 to 128 kg (-149.9 to 282.2 lb) |
- |
Number of Present DTC |
Number of present DTC recorded/ Min.: 0, Max.: 255 |
0 |
- |
Number of Past DTC |
Number of past DTC recorded/ Min.: 0, Max.: 255 |
0 |
- |
SD Card Communication Malfunction (B158C)
DESCRIPTION
The navigation receiver assembly stores this DTC when the SD card (disc player
disc) cannot be mounted when inserted into the SD card (disc player disc) slot.
DTC No.
DTC Detection Condition
Trouble Area
...
Lost Communication with ECM / PCM "A" (U0100)
DESCRIPTION
The power management control ECU receives shift position information from 2 sources.
It receives a shift position P signal from the shift lock control unit assembly
via a direct line, and shift position information from the ECM via CAN. If the ...
Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) (P0776)
SYSTEM DESCRIPTION
The TCM uses the vehicle speed signal and signals from the transmission speed
sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the TCM compares the actual gear with the shift schedule in the TCM memo ...