Toyota Venza manuals

Toyota Venza: Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Mirror L / Data List.

(e) Read the Data List according to the display on the Techstream.

Mirror L

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Seat Memory Switch1

M1 switch / ON or OFF

ON: M1 switch on

OFF: M1 switch off

-

Seat Memory Switch2

M2 switch / ON or OFF

ON: M2 switch on

OFF: M2 switch off

-

Seat Memory Switch3*

M3 switch / ON or OFF

ON: M3 switch on

OFF: M3 switch off

Not applicable

Seat Memory Set SW

SET switch / ON or OFF

ON: SET switch on

OFF: SET switch off

-

+B Voltage Input Value

Power supply for outer mirror control ECU assembly LH / MIN: 0 V, MAX: 19.98 V

Within range from 11 to 14 V

-

  • *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.

(f) Enter the following menus: Body Electrical / Driver Seat / Data List.

(g) Read the Data List according to the display on the Techstream.

Driver Seat

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Reclining Rear

Reclining switch signal (Rearward) / ON or OFF

ON: Reclining switch (Rearward) on

OFF: Reclining switch (Rearward) off

-

Reclining Front

Reclining switch signal (Forward) / ON or OFF

ON: Reclining switch (Forward) on

OFF: Reclining switch (Forward) off

-

Front Vertical Down

Front vertical switch signal (Downward) / ON or OFF

ON: Front vertical switch (Downward) on

OFF: Front vertical switch (Downward) off

-

Front Vertical Up

Front vertical switch signal (Upward) / ON or OFF

ON: Front vertical switch (Upward) on

OFF: Front vertical switch (Upward) off

-

Lifter Switch Down

Lifter switch signal (Downward) / ON or OFF

ON: Lifter switch (Downward) on

OFF: Lifter switch (Downward) off

-

Lifter Switch Up

Lifter switch signal (Upward) / ON or OFF

ON: Lifter switch (Upward) on

OFF: Lifter switch (Upward) off

-

Slide Rear

Slide switch signal (Rearward) / ON or OFF

ON: Slide switch (Rearward) on

OFF: Slide switch (Rearward) off

-

Slide Front

Slide switch signal (Forward) / ON or OFF

ON: Slide switch (Forward) on

OFF: Slide switch (Forward) off

-

Seat Memory No1

Seat position memorized with M1 switch / Mem or Not Mem

Mem: Memorized

Not Mem: Not memorized

-

Seat Memory No2

Seat position memorized with M2 switch / Mem or Not Mem

Mem: Memorized

Not Mem: Not memorized

-

Seat Memory No3*

Seat position memorized with M3 switch / Mem or Not Mem

Mem: Memorized

Not Mem: Not memorized

Not applicable

Ignition Switch

Communication state of ignition switch signal / ON or OFF

ON: Ignition switch ON signal received

OFF: Ignition switch off signal not received

-

P Switch

Park state signal / ON or OFF

ON: Shift lever in P

OFF: Shift lever in a position other than P

-

Parking Brake SW

Parking brake switch status / ON or OFF

ON: Parking brake applied

OFF: Parking brake released

-

Vehicle Speed

Vehicle speed data / min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)

Actual vehicle speed

-

Power Voltage

Power supply for position control ECU and switch assembly / min: 0.95 V, max: 20.84 V

Within range from 11 V to 14 V

-

Slide Position

Seat sliding position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Reclining Position

Seat reclining position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Front Vertical Position

Seat front vertical position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Lifter Position

Seat lifter position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Slide Pos Mem No1

Seat slide position memorized with M1 switch / min: 0000, max: 65535

Within range from 0000 to 65535

-

Reclining Pos Mem No1

Seat reclining position memorized with M1 switch / min: 0000, max: 65535

Within range from 0000 to 65535

-

Frnt Vrtcl Pos Mem No1

Front vertical position memorized with M1 switch / min: 0000, max: 65535

Within range from 0000 to 65535

-

Lifter Pos Mem No1

Lifter position memorized with M1 switch / min: 0000, max: 65535

Within range from 0000 to 65535

-

Slide Pos Mem No2

Seat slide position memorized with M2 switch / min: 0000, max: 65535

Within range from 0000 to 65535

-

Reclining Pos Mem No2

Seat reclining position memorized with M2 switch / min: 0000, max: 65535

Within range from 0000 to 65535

-

Frnt Vrtcl Pos Mem No2

Front vertical position memorized with M2 switch / min: 0000, max: 65535

Within range from 0000 to 65535

-

Lifter Pos Mem No2

Lifter position memorized with M2 switch / min: 0000, max: 65535

Within range from 0000 to 65535

-

Slide Pos Mem No3*

Seat slide position memorized with M3 switch / min: 0000, max: 65535

Within range from 0000 to 65535

Not applicable

Reclining Pos Mem No3*

Seat reclining position memorized with M3 switch / min: 0000, max: 65535

Within range from 0000 to 65535

Not applicable

Frnt Vrtcl Pos Mem No3*

Front vertical position memorized with M3 switch / min: 0000, max: 65535

Within range from 0000 to 65535

Not applicable

Lifter Pos Mem No3*

Lifter position memorized with M3 switch / min: 0000, max: 65535

Within range from 0000 to 65535

Not applicable

Headrest Switch UP*

Headrest switch signal (UP) / ON or OFF

ON: Headrest switch (UP) on

OFF: Headrest switch (UP) off

Not applicable

Headrest Switch Down*

Headrest switch signal (Down) / ON or OFF

ON: Headrest switch (Down) on

OFF: Headrest switch (Down) off

Not applicable

Motor Status

State of slide motor control / STANDBY, MOVING, LOCK

STANDBY: Slide motor idle

MOVING: Slide motor moving

LOCK: Slide motor locked

-

Lifter Initialize Flag

Seat lifter limit position memory / ON or OFF

ON: Memorized

OFF: Not memorized

-

Front Vertical Init Flag

Seat front vertical limit position memory / ON or OFF

ON: Memorized

OFF: Not memorized

-

Reclining Position Init Flg

Seat reclining limit position memory / ON or OFF

ON: Memorized

OFF: Not memorized

-

Slide Position Init Flag

Seat slide limit position memory / ON or OFF

ON: Memorized

OFF: Not memorized

-

Slide Position Front Limit

Seat sliding position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Slide Position Rear Limit

Seat slide position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Reclining Position Front Limit

Seat reclining position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Reclining Position Rear Limit

Seat reclining position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Front Vertical UP Limit

Seat front vertical position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Front Vertical Down Limit

Seat front vertical position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Lifter Position UP Limit

Seat lifter position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Lifter Position Down Limit

Seat lifter position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Shift P sw(PMN)*

Park state signal / ON or OFF

ON: Shift lever in P

OFF: Shift lever in a position other than P

Not applicable

Memory Button Buzzer Request

Driver seat buzzer request display / OFF, MOVE, REGISTRY, CANCEL, REG NG, REG WAIT

OFF: Buzzer does not sound

MOVE: Request to sound buzzer when starting memory replay

REGISTRY: Request to sound buzzer when starting memory registration

CANCEL: Request to sound buzzer when canceling memory call registration

REG NG: Request to sound buzzer when memory call registration not possible

REG WAIT: Request to sound buzzer when starting memory call cabin scan

-

Driver Seat Request Command

Driver seat operation request received / OFF, MEMORY, MEM MOV, MEM SOD, RET MOV, AWY MOV, AWY SOD, MEM AWY or MEM RET

OFF: No instruction

MEMORY: Request to memorize

MEM MOV: Request to recall memory

MEM SOD: Request to replay

RET MOV: Request to return

AWY MOV: Request to move away

AWY SOD: Request to recall away position memory

MEM AWY: Request to recall memorized position of seatback

MEM RET: Request to restore seatback to memorized position

-

Driver Seat POS REQ

Seat memory switch operation value / OFF, MEM1, MEM2, MEM3*, DRV1*, DRV2* or DRV3*

OFF: No operation

MEM1: M1 switch operation status

MEM2: M2 switch operation status

MEM3: M3 switch operation status*

DRV1: Other 1 operation status*

DRV2: Other 2 operation status*

DRV3: Other 3 operation status*

-

Away Move Range Scale

The seat travel distance for the power easy access system / NONE, SMALL, STANDARD or LONG

NONE: Seat travel distance none

SMALL: Seat travel distance short

STANDARD: Seat travel distance normal

LONG: Seat travel distance long

-

Return Move

Return function / NOT AVL or AVAIL

NOT AVL: Not available

AVAIL: Available

-

Return & Away Function

Return & away function / NOT AVL or AVAIL

NOT AVL: Not available

AVAIL: Available

-

Driver Seat Buckle SW

Driver seat belt buckle switch / ON or OFF

ON: Driver seat belt fastened

OFF: Driver seat belt unfastened

-

Return Position

Return position / min: 0000, max: 65535

Within range from 0000 to 65535

-

Sensor Power Voltage

Sensor Power Voltage / min: 0 V, max: 19.89 V

Within range from 11 to 14 V

-

Number of Trouble Codes

Number of trouble codes / min.: 0 or max.: 255

Number of DTCs will be displayed

-

  • *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.

(h) Enter the following menus: Body Electrical / Main Body / Data List.

(i) Read the Data List according to the display on the Techstream.

Main Body

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

D Door Courtesy SW

Front door courtesy light switch assembly LH signal / ON or OFF

ON: Driver door open

OFF: Driver door closed

-

Door Lock SW-Lock

Door control switch (power window regulator master switch assembly) lock signal / ON or OFF

ON: Lock side of door control switch (power window regulator master switch assembly) pushed

OFF: Lock side of door control switch (power window regulator master switch assembly) not pushed

-

Door Lock SW-Unlock

Door control switch (power window regulator master switch assembly) unlock signal / ON or OFF

ON: Unlock side of door control switch (power window regulator master switch assembly) pushed

OFF: Unlock side of door control switch (power window regulator master switch assembly) not pushed

-

Mem SW No. w/KeyID1

Memory switch linked with key ID1 / NONE, MEM SW1, MEM SW2, or MEM SW3*

NONE: No switches linked with key ID1

MEM SW1: M1 switch linked with key ID1

MEM SW2: M2 switch linked with key ID1

MEM SW3: M3 switch linked with key ID1*

-

Mem SW No. w/KeyID2

Memory switch linked with key ID2 / NONE, MEM SW1, MEM SW2, or MEM SW3*

NONE: No switches linked with key ID2

MEM SW1: M1 switch linked with key ID2

MEM SW2: M2 switch linked with key ID2

MEM SW3: M3 switch linked with key ID2*

-

Mem SW No. w/KeyID3

Memory switch linked with key ID3 / NONE, MEM SW1, MEM SW2, or MEM SW3*

NONE: No switches linked with key ID3

MEM SW1: M1 switch linked with key ID3

MEM SW2: M2 switch linked with key ID3

MEM SW3: M3 switch linked with key ID3*

-

Mem SW No. w/KeyID4

Memory switch linked with key ID4 / NONE, MEM SW1, MEM SW2, or MEM SW3*

NONE: No switches linked with key ID4

MEM SW1: M1 switch linked with key ID4

MEM SW2: M2 switch linked with key ID4

MEM SW3: M3 switch linked with key ID4*

-

Mem SW No. w/KeyID5

Memory switch linked with key ID5 / NONE, MEM SW1, MEM SW2, or MEM SW3*

NONE: No switches linked with key ID5

MEM SW1: M1 switch linked with key ID5

MEM SW2: M2 switch linked with key ID5

MEM SW3: M3 switch linked with key ID5*

-

Mem SW No. w/KeyID6

Memory switch linked with key ID6 / NONE, MEM SW1, MEM SW2, or MEM SW3*

NONE: No switches linked with key ID6

MEM SW1: M1 switch linked with key ID6

MEM SW2: M2 switch linked with key ID6

MEM SW3: M3 switch linked with key ID6*

-

Mem SW No. w/KeyID7

Memory switch linked with key ID7 / NONE, MEM SW1, MEM SW2, or MEM SW3*

NONE: No switches linked with key ID7

MEM SW1: M1 switch linked with key ID7

MEM SW2: M2 switch linked with key ID7

MEM SW3: M3 switch linked with key ID7*

-

Driver Seat Memory1

Seat position memorized with M1 switch / OFF or ON

OFF: Not memorized

ON: Memorized

-

Driver Seat Memory2

Seat position memorized with M2 switch / OFF or ON

OFF: Not memorized

ON: Memorized

-

Driver Seat Memory3*

Seat position memorized with M3 switch / OFF or ON

OFF: Not memorized

ON: Memorized

Not applicable

  • *: Although the item is displayed on the Techstream, it is not applicable to this vehicle.

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Driver Seat / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Driver Seat

Tester Display

Test Part

Control Range

Diagnostic Note

Seat Reclining

Seat reclining operation

OFF/Front/Rear

-

Front Vertical Operation

Seat front vertical operation

OFF/Up/Down

-

Lifter Operation

Seat lifter operation

OFF/Up/Down

-

Seat Slide Operation

Seat slide operation

OFF/Front/Rear

-

Buzzer

Buzzer operation

OFF/ON

-

Dtc Check / Clear
DTC CHECK / CLEAR 1. CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Driver Seat ...

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART If a trouble code is displayed during the DTC check, inspect the trouble areas listed for that code. For details of the code, refer to the ''See page'' ...

Other materials about Toyota Venza:

Initialization
INITIALIZATION 1. RESET BACK DOOR CLOSE POSITION NOTICE: Perform initialization of the power back door system (power back door ECU initialization) if one of the following is performed: The cable is disconnected from the negative (-) battery termin ...

Power Seat does not Return to Memorized Position
DESCRIPTION When either the M1 or M2 switch is pressed, the outer mirror control ECU assembly LH sends a switch signal to the main body ECU (driver side junction block assembly) via CAN communication. Then, the main body ECU (driver side junction block as ...

Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1) (P0748)
DESCRIPTION Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid ...

© 2016-2024 Copyright www.tovenza.com

0.1304