Toyota Venza: Data List / Active Test
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof / Data List.
(e) Read the Data List according to the display on the Techstream.
Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Open SW |
SLIDE OPEN switch signal/ON or OFF |
ON: SLIDE OPEN switch pressed OFF: SLIDE OPEN switch not pressed |
- |
|
Close SW |
SLIDE CLOSE switch signal/ON or OFF |
ON: SLIDE CLOSE switch pressed OFF: SLIDE CLOSE switch not pressed |
- |
|
Up SW |
TILT UP switch signal/ON or OFF |
ON: TILT UP switch pressed OFF: TILT UP switch not pressed |
- |
|
Down SW |
TILT DOWN switch signal/ON or OFF |
ON: TILT DOWN switch pressed OFF: TILT DOWN switch not pressed |
- |
|
Hall IC1 Pulse |
Sliding roof operation signal/LO or HI |
LO: Sliding roof motor not operating HI: Sliding roof motor operating |
- |
|
Hall IC1 Status |
Sliding roof operation signal/NORMAL or LOCK |
NORMAL: Sliding roof motor operating LOCK: Sliding roof motor not operating |
- |
|
Hall IC2 Pulse |
Sliding roof operation signal/LO or HI |
LO: Sliding roof motor not operating HI: Sliding roof motor operating |
- |
|
Hall IC2 Status |
Sliding roof operation signal/NORMAL or LOCK |
NORMAL: Sliding roof motor operating LOCK: Sliding roof motor not operating |
- |
|
Ignition (Direct Signal) |
Ignition switch signal/ON or OFF |
ON: Ignition switch ON OFF: Ignition switch off |
- |
|
Ignition (MPX) |
Ignition switch signal (MPX signal)/ON or OFF |
ON: Ignition switch ON OFF: Ignition switch off |
- |
|
Door Courtesy |
Driver's door courtesy light switch signal/ON or OFF |
ON: Driver's door open OFF: Driver's door closed |
- |
|
Key Off Permission |
Key-off sliding roof operation permit signal/ON or OFF |
ON: Front doors are not opened within 45 seconds after ignition switch turned off OFF: Any status except "ON" status |
- |
|
Open Switch Failure (Past) |
Open switch failure signal (Past)/Fail or Not Fail |
Fail: Sliding roof open signal failure (Past) Not Fail: Sliding roof open signal not fail (Past) |
- |
|
Close Switch Failure (Past) |
Close switch failure signal (Past)/Fail or Not Fail |
Fail: Sliding roof close signal failure (Past) Not Fail: Sliding roof close signal not fail (Past) |
- |
|
Up Switch Failure (Past) |
Up switch failure signal (Past)/Fail or Not Fail |
Fail: Sliding roof tilt up signal failure (Past) Not Fail: Sliding roof tilt up signal not fail (Past) |
- |
|
Down Switch Failure (Past) |
Down switch failure signal (Past)/Fail or Not Fail |
Fail: Sliding roof tilt down signal failure (Past) Not Fail: Sliding roof tilt down signal not fail (Past) |
- |
|
Open Switch Failure (Current) |
Open switch failure signal (Current)/Fail or Not Fail |
Fail: Sliding roof open signal failure (Current) Not Fail: Sliding roof open signal not fail (Current) |
- |
|
Close Switch Failure (Current) |
Close switch failure signal (Current)/Fail or Not Fail |
Fail: Sliding roof close signal failure (Current) Not Fail: Sliding roof close signal not fail (Current) |
- |
|
Up Switch Failure (Current) |
Up switch failure signal (Current)/Fail or Not Fail |
Fail: Sliding roof tilt up signal failure (Current) Not Fail: Sliding roof tilt up signal not fail (Current) |
- |
|
Down Switch Failure (Current) |
Down switch failure signal (Current)/Fail or Not Fail |
Fail: Sliding roof tilt down signal failure (Current) Not Fail: Sliding roof tilt down signal not fail (Current) |
- |
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Slide Roof |
Operate sliding roof |
CLOS/UP / OFF |
- |
|
Slide Roof |
Operate sliding roof |
OPN/DWN / OFF |
- |
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
(a) Disconnect the P4 ECU connector.
(b) Measure the resistance and voltage according to the value(s) in the tabl ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roo ...
Other materials about Toyota Venza:
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting
the cable from the negative (-) battery terminal. Therefore, make sure to read the
disconnecting the cable from the negativ ...
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK POWER MANAGEMENT CONTROL ECU
(a) Disconnect the D42 and D43 connectors.
(b) Measure the voltage and resistance according to the value(s) in the table
below.
Tester Connection
Wiring Color
Termi ...
System Description
SYSTEM DESCRIPTION
1. GENERAL
The windshield deicer system's thin heater wires are attached to the inside of
the front window and deice the window surface quickly. The indicator light illuminates
while the system is operating. The system automaticall ...
0.14