Toyota Venza: Data List / Active Test

Toyota Venza Service Manual / Lighting (ext) / Lighting System / Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

CAUTION:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / (desired system) / Data List.

(e) Read the Data List according to the display on the Techstream.

Main Body

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
IG SW	Ignition switch or engine switch IG signal/ON or OFF	ON: Ignition switch ON OFF: Ignition switch off	-
Parking Brake SW	Parking brake switch signal/ON or OFF	ON: Parking brake switch on OFF: Parking brake switch off	-
D Door Courtesy SW	Driver side door courtesy switch signal/ON or OFF	ON: Driver side door open OFF: Driver side door closed	-
P Door Courtesy SW	Front passenger side door courtesy switch/ON or OFF	ON: Front passenger side door open OFF: Front passenger side door closed	-
RR Door Courtesy SW	Rear door courtesy switch RH/ON or OFF	ON: Rear door RH open OFF: Rear door RH closed	-
RL Door Courtesy SW	Rear door courtesy switch LH/ON or OFF	ON: Rear door LH open OFF: Rear door LH closed	-
Dimmer SW	Dimmer switch high position signal/ON or OFF	ON: Dimmer switch in high or high flash position OFF: Dimmer switch in low position	-
Passing Light SW	Dimmer switch high flash position (pass) signal/ON or OFF	ON: Dimmer switch in high flash position OFF: Dimmer switch not in high flash position	-
Front Fog Light SW	Front fog light switch signal/ON or OFF	ON: Front fog light switch on OFF: Front fog light switch off	-
Auto Light SW	Light control switch auto position signal/ON or OFF	ON: Light control switch in AUTO position OFF: Light control switch not in AUTO position	-
Head Light SW (Head)	Light control switch head position signal/ON or OFF	ON: Light control switch in head position OFF: Light control switch not in head position	-
Head Light SW (Tail)	Light control switch tail position signal/ON or OFF	ON: Light control switch in tail or head position OFF: Light control switch in neither tail nor head position	-
Illumination Rate Info	Illumination rate information/0 ms. to 99.99 ms.	Value is output according to ambient light levels	-
Auto H Beam STS0	Automatic high beam sensor current state/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err	Condition can be displayed	Undetec: undetected CAM NA: camera detection malfunction No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: malfunction Delay: standby mode Aim Lmt: aiming misalignment SAE Mod: SAE mode Undefin: undefined state LIN Err: LIN communication error
Auto H Beam STS1	Automatic high beam sensor state past 1/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err	Condition can be displayed	Undetec: undetected CAM NA: camera detection malfunction No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: malfunction Delay: standby mode Aim Lmt: aiming misalignment SAE Mod: SAE mode Undefin: undefined state LIN Err: LIN communication error
Auto H Beam STS2	Automatic high beam sensor state past 2/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err	Condition can be displayed	Undetec: undetected CAM NA: camera detection malfunction No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: malfunction Delay: standby mode Aim Lmt: aiming misalignment SAE Mod: SAE mode Undefin: undefined state LIN Err: LIN communication error
Auto H Beam STS3	Automatic high beam sensor state past 3/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err	Condition can be displayed	Undetec: undetected CAM NA: camera detection malfunction No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: malfunction Delay: standby mode Aim Lmt: aiming misalignment SAE Mod: SAE mode Undefin: undefined state LIN Err: LIN communication error
Auto H Beam STS4	Automatic high beam sensor state past 4/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err	Condition can be displayed	Undetec: undetected CAM NA: camera detection malfunction No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: malfunction Delay: standby mode Aim Lmt: aiming misalignment SAE Mod: SAE mode Undefin: undefined state LIN Err: LIN communication error
Auto H Beam STS5	Automatic high beam sensor state past 5/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err	Condition can be displayed	Undetec: undetected CAM NA: camera detection malfunction No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: malfunction Delay: standby mode Aim Lmt: aiming misalignment SAE Mod: SAE mode Undefin: undefined state LIN Err: LIN communication error
Auto H Beam STS6	Automatic high beam sensor state past 6/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err	Condition can be displayed	Undetec: undetected CAM NA: camera detection malfunction No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: malfunction Delay: standby mode Aim Lmt: aiming misalignment SAE Mod: SAE mode Undefin: undefined state LIN Err: LIN communication error
Auto H Beam STS7	Automatic high beam sensor state past 7/Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err	Condition can be displayed	Undetec: undetected CAM NA: camera detection malfunction No sens: no detection Hlight: oncoming vehicles with headlights on Taillgt: preceding vehicles with taillights on Speed: vehicle speed Daytime: daytime state Village: urban area Malfunc: malfunction Delay: standby mode Aim Lmt: aiming misalignment SAE Mod: SAE mode Undefin: undefined state LIN Err: LIN communication error

AFS

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Steering Sens Signal	Steering angle sensor signal value/-384 deg. to 382.5 deg.	Value is output according to steering wheel position	-
Steering Sens Center Pos	Steering angle sensor center position/-3072 deg. to 3070.5 deg.	Approx. 0 deg. (When steering wheel is straight)	-
FR Wheel Speed	Front right wheel speed/0 to 327.67 km/h	Condition can be displayed	-
Number Of Trouble Codes	Number of trouble codes/0 to 255	Condition can be displayed	-

HL Auto Leveling

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Headlight Low Beam State	Low beam headlight state/ON or OFF	ON: Low beam headlights on OFF: Low beam headlights off	-
+B	IG power supply voltage value/0.00 to 19.75 V	11 to 14 V	-
Height Sens Pw Supply Val	Height control sensor power supply value/0.00 to 5.00 V	Approx. 5 V	-
Rr Height Sens Signal Val	Rear height control sensor signal value/0.00 to 5.00 V	Approx. 2.5 V (When vehicle is level)	Value changes according to vehicle height
Vehicle Speed	Vehicle speed/0.00 to 327.67 km/h (203.61 mph)	Condition can be displayed	-
Rear Height Adjust Valid Flag	Rear height adjustment range/VALID or INVALID	Condition can be displayed	-
Init Writing Count	Number of times for initialization/0 to 255	Condition can be displayed	-
Sensor Initialization Hist	Sensor Initialization History/not comp, 10%, 25%, 50%, 75%, 100% or complied	Condition can be displayed	-
Number Of Trouble Codes	Number of trouble codes/0 to 255	Condition can be displayed	-

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / (desired system) / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Main Body

Tester Display	Test Part	Control Range	Diagnostic Note
Daytime Running Light	Daytime running light relay	ON/OFF	-
Taillight Relay	Taillight relay	ON/OFF	-
Headlight Relay	Low beam headlight relay	ON/OFF	-
Head Light Hi	High beam headlight relay	ON/OFF	-
Front Fog Light Relay	Front fog light relay	ON/OFF	-
Side Mirror Foot Light*1	Door mirror foot lights	ON/OFF	-

*1: w/o Seat Position Memory

Mirror L*2

Tester Display	Test Part	Control Range	Diagnostic Note
Foot Light	Door mirror foot light LH	ON/OFF	-

Mirror R*2

Tester Display	Test Part	Control Range	Diagnostic Note
Foot Light	Door mirror foot light RH	ON/OFF	-

*2: w/ Seat Position Memory

HL Auto Leveling

Tester Display	Test Part	Control Range	Diagnostic Note
Drive The Leveling Motor UP*3	Leveling motor upward operation	ON/OFF	ON: Moves up OFF: Stops
Drive The Leveling Motor DOWN*3	Leveling motor downward operation	ON/OFF	ON: Moves down OFF: Stops

Tester Display

Test Part

Control Range

Diagnostic Note

Drive The Leveling Motor UP*3

Leveling motor upward operation

ON/OFF

ON: Moves up

OFF: Stops

Drive The Leveling Motor DOWN*3

Leveling motor downward operation

ON/OFF

ON: Moves down

OFF: Stops

*3: Perform the active test with the engine running.

Freeze Frame Data

FREEZE FRAME DATA 1. FREEZE FRAME DATA (a) Whenever a DTC is detected, the AFS ECU (headlight swivel ECU assembly) stores the current vehicle (sensor) state as Freeze Frame Data. 2. CHECK FREEZE ...

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART Lighting System DTC Code Detection Item See page B1244 Light Sensor Circuit Malfunction ...

Other materials about Toyota Venza:

Internal Control Module Throttle Position Performance (P060E)
MONITOR DESCRIPTION The ECM monitors the input signals of the throttle position sensor No. 1 and stop light switch. As the ECM monitors the input signals of the throttle position sensor No. 1 and the STP signals of the stop light switch, if the input sign ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY) (a) Disconnect the main body ECU (driver side junction block assembly) connectors. (b) Measure the resistance and voltage according to the value(s) in the table below. ...

System Description
SYSTEM DESCRIPTION 1. ILLUMINATED ENTRY SYSTEM (a) The illuminated entry system has the following control functions: Control Outline Lights that Operate Actuation Area-linked*2 When a registered k ...