Toyota Venza: Data List / Active Test

Toyota Venza Service Manual / Cruise Control / Cruise Control System / Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Powertrain / Cruise Control / Data List.

(e) Read the Data List according to the display on the Techstream.

Cruise Control (ECM)

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
CCS Vehicle Spd	Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)	Actual vehicle speed	-
CCS Mem Vehicle Spd	Cruise control memorized speed / Min.: 0 km/h (0 mph), Max.: 200 km/h (125 mph)	Stored vehicle speed	-
Throttle Opening Angle	Throttle opening angle / Min.: 0°, Max.: 125°	Demanded throttle angle	-
Cruise Control	Cruise control system active condition / ON or OFF	ON: Cruise control activated OFF: Cruise control deactivated	-
Main SW M-CPU	Main switch signal (Main CPU) / ON or OFF	ON: Main switch on OFF: Main switch off	-
CCS Ready M-CPU	Cruise control system standby condition (Main CPU) / ON or OFF	Each time main switch is pushed, display changes between ON and OFF	-
CCS Indicator M-CPU	CRUISE main indicator signal (Main CPU) / ON or OFF	ON: CRUISE main indicator light on OFF: CRUISE main indicator light off	-
Cancel Switch	CANCEL switch signal / ON or OFF	ON: CANCEL switch on OFF: CANCEL switch off	-
SET/COAST Switch	- / SET switch signal / ON or OFF	ON: - / SET switch on OFF: - / SET switch off	-
RES/ACC Switch	+ / RES switch signal / ON or OFF	ON: + / RES switch on OFF: + / RES switch off	-
Stp Light SW M-CPU	Stop light switch signal (Main CPU) / ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-
Cruise Operation Status	Park/neutral position switch signal (D position) / ON or OFF	ON: Shift lever in D OFF: Shift lever not in D	-

HINT:

If any DTCs are output, the value for a measurement item may be incorrect.
If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body / Combination Meter / Active Test.

(e) Perform Active Test according to the display on the Techstream.

HINT:

The ignition switch must be turned to ON to proceed with the Active Test using the Techstream.

Combination Meter

Tester Display	Test Part	Control Range	Diagnostic Note
Indicat. Lamp Cruise	CRUISE main indicator light	OFF or ON	Confirm that the vehicle is stopped with the engine idling
Indicat. SET	SET indicator light	OFF or BLINK	Confirm that the vehicle is stopped with the engine idling

Fail-safe Chart

FAIL-SAFE CHART HINT: If the following conditions are detected while the cruise control is in operation, the system clears the stored vehicle speed in the ECM and cancels the cruise control oper ...

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART If a trouble code is displayed during the DTC check, check the trouble areas listed for that code in the table below and proceed to the appropriate page. Cruise Contr ...

Other materials about Toyota Venza:

Evaporative Emission Control System Leak Detected (Gross Leak) (P0455,P0456)
DTC SUMMARY DTC No. Monitoring Item Malfunction Detection Condition Trouble Area Detection Timing Detection Logic P0455 EVAP gross leak Leak detection pum ...

Diagnosis System
DIAGNOSIS SYSTEM 1. ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM (a) CAN No. 1 Bus (1) ECM (2) Main body ECU (Driver side junction block) (3) Combination meter (4) Power steering ECU (5) Air conditioning amplifier*3 (6) Center air ...

Removal
REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. PRECAUTION CAUTION: Be sure to read Precaution thoroughly before servicing (See page ...