Toyota Venza manuals

Toyota Venza: Customize Parameters

CUSTOMIZE PARAMETERS

PROCEDURE

1. CUSTOMIZE INTUITIVE PARKING ASSIST SYSTEM

(a) Customizing with the Techstream

NOTICE:

  • When the customer requests a change in a function, first make sure that the function can be customized.
  • Be sure to make a note of the current settings before customizing.
  • When troubleshooting a function, first make sure that the function is set to the default setting.

(1) Connect the Techstream to the DLC3.

(2) Turn the engine switch on (IG).

(3) Turn the clearance sonar main switch on.

(4) Turn the Techstream on.

(5) Enter the following menus: Body Electrical / Intuitive P/A / Utility / Customize.

(6) Select the setting by referring to the table below.

Warning

Display

Default

Content

Setting

Relevant ECU

Rr Sensor Onset Range

Wide

Sets the buzzer activation range for the rear center sensors.

Narrow or Wide

  • Narrow: 600 mm (23.6 in.)
  • Wide: 1000 mm (39.4 in.) (Pole)
  • Wide: 1500 mm (59.1 in.) (Wall)

Clearance warning ECU assembly

Keep Sense Buzzer

Avail

Sounds the buzzer when the distance between the vehicle and obstacle does not change for more than 3 seconds.

Not Avail or Avail

  • Not Avail: Not Available
  • Avail: Available

Clearance warning ECU assembly

Fr & Rr Buzzer Volume

M2

Changes the buzzer volume setting.

L, M1, M2, M3 or H

  • L: Low volume
  • M1: Medium low volume
  • M2: Medium volume
  • M3: Medium high volume
  • H: High volume

Clearance warning ECU assembly

Sensor

Display

Default

Content

Setting

Relevant ECU

Sensor Condition N

Avail

Makes the front sensors available when the shift lever is in N.

Not Avail or Avail

  • Not Avail: Not Available
  • Avail: Available

Clearance warning ECU assembly

Reverse Range Front Sensor

F

Changes the operation setting for the front sensors when the shift lever is in R.

F or F Stop

  • F: Front sensors are available
  • F Stop: Front sensors are not available

Clearance warning ECU assembly

Non P/R Range Rear Sensor

R Stop

Changes the operation setting for the rear sensors when the shift lever is in any position other than P or R.

R, Rcrn or R Stop

  • R: All rear sensors are available
  • Rcrn: Rear corner sensors are available
  • R Stop: All rear sensors are not available

Clearance warning ECU assembly

How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the intuitive parking assist system. *: Use the Techstream. PROCEDURE 1. VEHI ...

Operation Check
OPERATION CHECK 1. MALFUNCTION BUZZER (a) Open circuit or frozen (1) If an open circuit is detected between the ultrasonic sensors and the clearance warning ECU assembly, if a sensor malfunction ...

Other materials about Toyota Venza:

Radio Antenna Pole
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE ROOF ANTENNA POLE SUB-ASSEMBLY (a) Turn the roof antenna pole sub-assembly in the direction indicated by the arrow in the illustration to remove it. ...

Inspection
INSPECTION PROCEDURE 1. INSPECT REAR NO. 3 SPEAKER ASSEMBLY (for 13 Speakers) (a) With the speaker installed, check that there is no looseness or other abnormalities. (b) Check that there is no foreign matter in the speaker, no tears on the speaker cone ...

System Description
SYSTEM DESCRIPTION 1. POWER MIRROR CONTROL SYSTEM DESCRIPTION (a) This system has the following functions: power retract mirror function*, reverse shift-linked function, electrical remote control function, memory function and mirror heater function. ...

© 2016-2024 Copyright www.tovenza.com

0.1582