Toyota Venza: Customize Parameters

Toyota Venza Service Manual / Theft Deterrent / Keyless Entry / Smart Key System(for Entry Function) / Customize Parameters

CUSTOMIZE PARAMETERS

1. CUSTOMIZING FUNCTION WITH TECHSTREAM

HINT:

The items in the table below can be customized.

NOTICE:

When the customer requests a change in a function, first make sure that the function can be customized.
Be sure to make a note of the current setting before customizing.
When troubleshooting a function, first make sure that the function is set to the default setting.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Smart Key / Utility / Customize Setting.

(e) Select the setting by referring to the table below.

Smart Key

Tester Display	Default	Content	Setting
Ignition Available Area	All	Function that switches the entry ignition detection area	Front or All
Park Wait Time	2.5 s	Function that sets waiting time to permit opening door after door is locked with entry lock function	0.5 s, 1.5 s, 2.5 s, or 5 s
Back Door Opening Operation	Long	Function that opens the back door when the driver has the key and presses back door opener switch assembly (opener switch)	Long, Twice or OFF
Key Low Battery Warning	ON	Function that warns driver that key battery is weak	ON or OFF

2. ENTRY UNLOCK MODE SWITCHING

(a) Check that the power source mode is OFF and the LED on the key is not blinking. Press the LOCK button and one of the other buttons on the key at the same time for approximately 5 seconds while the key is in the actuation area.

Driver door unlock default setting:

When the switches are pressed and held for 5 seconds, the entry door unlock mode changes to the mode that is not currently selected.

NOTICE:

After pressing and holding the switches for 5 seconds, wait 5 seconds before performing the same procedure again.

Driver door unlock mode:
When the driver door touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.
All door unlock mode:
When any touch sensor is touched, all doors unlock.

(b) The certification ECU (smart key ECU assembly) receives this signal from the door control receiver assembly and changes the smart key system to the entry unlock mode.

(c) The certification ECU (smart key ECU assembly) sounds the buzzers of the wireless door lock buzzer and combination meter to inform the user that the mode has been changed.

HINT:

The procedure only changes the entry unlock mode of the smart key system. It does not switch the unlocking of the wireless door lock control.

3. ELECTRICAL KEY CANCEL

The electrical key cancel operation disables the following functions:

Entry Unlock/Lock
Entry Ignition
Entry Back Door Open
Electrical Key Lock-in Prevention
Warning

(a) The operation procedures are as follows:

Precondition:

Engine switch off, driver side door closed and unlocked.

(1) Push the unlock switch of the key once.

(2) Open the driver door within 5 seconds.

(3) Push the unlock switch of the key twice within 5 seconds.

(4) Close and open the driver door twice within 30 seconds.

(Driver door: Close → Open → Close → Open)

(5) Push the unlock switch of the key twice within 5 seconds.

(6) Close and open the driver door within 30 seconds.

(Driver door: Close → Open)

(7) Close the driver door within 5 seconds.

When electrical key cancel is activated, the wireless door lock buzzer sounds twice.

To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

Operation Check

OPERATION CHECK 1. SMART KEY SYSTEM OPERATION INSPECTION (a) Check the entry unlock function. (1) Use the wireless lock operation to lock the doors. With the key outside the vehicle, touch a fron ...

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order ...

Other materials about Toyota Venza:

Driving the vehicle
The following procedures should be observed to ensure safe driving. - Starting the engine - Driving With the brake pedal depressed, shift the shift lever to “D”. Release the parking brake. Gradually release the brake pedal and gentl ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL REAR DRIVE SHAFT DUST COVER (a) Using SST and a steel plate, install a new rear drive shaft dust cover to the rear drive shaft inboard joint assembly. Text in Illustration *1 ...

Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) (P2808)
DESCRIPTION The TCM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). Then the TCM compares the actual gear with the shift schedule in the TCM memory to ...