Toyota Venza manuals

Toyota Venza: Clock Display Circuit

DESCRIPTION

The accessory meter assembly uses this circuit to communicate with the combination meter assembly via the direct line. The accessory meter assembly uses this circuit to receive the drive monitor switch signals from the combination meter assembly via the direct line and multi-information display signal from each ECU through the combination meter assembly via the direct line.

HINT:

Each ECU outputs the DTCs when each system has a malfunction.

WIRING DIAGRAM


PROCEDURE

1.

SYSTEM CHECK

(a) Confirm the symptom.

Result

Proceed to

Clock display does not indicate cruise information display (The display only illuminates).

A

Multi-information display does not change when the drive monitor switch is operated.

B


B

GO TO STEP 5


A

2.

CHECK CAN COMMUNICATION SYSTEM

(a) Check if a CAN communication DTC is output (See page ).


Result

Proceed to

CAN communication DTC is not output.

A

CAN communication DTC is output.

B


B

GO TO CAN COMMUNICATION SYSTEM


A

3.

CHECK HARNESS AND CONNECTOR (ACCESSORY METER ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the E2 and F2*1 or F5*2 connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F2-3 (HSI+)*1 - E2-4 (LCL+)

Always

Below 1 Ω

F2-4 (DATA)*1 - E2-5 (MDAT)

Always

Below 1 Ω

F2-16 (SYNC)*1 - E2-17 (SYNC)

Always

Below 1 Ω

F5-2 (HSI+)*2 - E2-4 (LCL+)

Always

Below 1 Ω

F5-12 (DATA)*2 - E2-5 (MDAT)

Always

Below 1 Ω

F5-6 (SYNC)*2 - E2-17 (SYNC)

Always

Below 1 Ω

E2-4 (LCL+) - Body ground

Always

10 kΩ or higher

E2-5 (MDAT) - Body ground

Always

10 kΩ or higher

E2-17 (SYNC) - Body ground

Always

10 kΩ or higher

F5-16 (SGND)*2 - Body ground

Always

Below 1 Ω

F2-12 (E) - Body ground

Always

Below 1 Ω

  • *1: w/o Multi-information Display
  • *2: w/ Multi-information Display

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

4.

INSPECT COMBINATION METER ASSEMBLY

(a) Reconnect the E2 connector.


(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

F2-3 (HSI+)*1 - Body ground

Ignition switch ON

Pulse generation

F2-4 (DATA)*1 - Body ground

Ignition switch ON

Pulse generation

F2-16 (SYNC)*1 - Body ground

Ignition switch ON

Pulse generation

F5-2 (HSI+)*2 - Body ground

Ignition switch ON

Pulse generation

F5-12 (DATA)*2 - Body ground

Ignition switch ON

Pulse generation

F5-6 (SYNC)*2 - Body ground

Ignition switch ON

Pulse generation

  • *1: w/o Multi-information Display
  • *2: w/ Multi-information Display
Text in Illustration

*1

Front view of wire harness connector

(to Accessory Meter Assembly (w/o Multi-information Display))

*2

Front view of wire harness connector

(to Accessory Meter Assembly (w/ Multi-information Display))


OK

REPLACE ACCESSORY METER ASSEMBLY


NG

REPLACE COMBINATION METER ASSEMBLY

5.

CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - DRIVE MONITOR SWITCH)

(a) Disconnect the E2 and D3 connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

E2-6 (A/B) - D3-5 (INFO)

Always

Below 1 Ω

E2-6 (A/B)- Body ground

Always

10 kΩ or higher

E2-7 (RSET) - D3-6 (SEL)

Always

Below 1 Ω

E2-7 (RSET) - Body ground

Always

10 kΩ or higher

E2-18 (E) - D3-7 (STUP)

Always

Below 1 Ω

E2-18 (E)- Body ground

Always

10 kΩ or higher

D3-3 (E) - Body ground

Always

Below 1 Ω


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

6.

INSPECT DRIVE MONITOR SWITCH

(a) Disconnect the D3 connector.


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3 (E) - 5 (INFO)

Ignition switch ON and INFO CLOCK*1 or INFO*2 switch pressed

Below 1 Ω

Ignition switch ON and INFO CLOCK*1 or INFO*2 switch released

10 kΩ or higher

3 (E) - 6 (SEL)

Ignition switch ON and RESET H*1 or SELECT RESET*2 switch pressed

Below 1 Ω

Ignition switch ON and RESET H*1 or SELECT RESET*2 switch released

10 kΩ or higher

3 (E) - 7 (STUP)

Ignition switch ON and US/M M*1 or SETUP*2 switch pressed

Below 1 Ω

Ignition switch ON and US/M M*1 or SETUP*2 switch released

10 kΩ or higher

  • *1: w/o Multi-information Display
  • *2: w/ Multi-information Display
Text in Illustration

*1

Component without harness connected

(Drive Monitor Switch)


OK

REPLACE COMBINATION METER ASSEMBLY


NG

REPLACE DRIVE MONITOR SWITCH

Meter Illumination is Always Dark
DESCRIPTION In this circuit, the meter CPU receives auto dimmer signals from the main body ECU (driver side junction block assembly) using the CAN communication system (CAN No. 1 Bus). When the m ...

Speed Signal Circuit
DESCRIPTION The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel spe ...

Other materials about Toyota Venza:

How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the air conditioning system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT ...

Removal
REMOVAL PROCEDURE 1. REMOVE BACK DOOR PANEL TRIM ASSEMBLY 2. REMOVE REAR WIPER ARM HEAD CAP 3. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY 4. REMOVE REAR WIPER MOTOR GROMMET 5. REMOVE REAR WIPER MOTOR AND BRACKET ASSEMBLY 6. REMOVE REAR LIGH ...

Display does not Dim when Light Control Switch is Turned ON
PROCEDURE 1. CHECK IMAGE QUALITY SETTING (a) Turn the light control switch to the tail or head position. (b) Check that the daytime screen setting on the display adjustment screen is set to on. Result ...

© 2016-2024 Copyright www.tovenza.com

0.1344