Toyota Venza: Brake Control / Dynamic Control Systems
- Brake Actuator
- Brake Pedal Load Sensing Switch
- Front Speed Sensor
- Rear Speed Sensor(for 2wd)
- Rear Speed Sensor(for Awd)
- Relay
- Steering Angle Sensor
- Vehicle Stability Control System
- Precaution
- Parts Location
- System Description
- System Diagram
- How To Proceed With Troubleshooting
- Calibration
- Check For Intermittent Problems
- Test Mode Procedure
- Problem Symptoms Table
- Terminals Of Ecu
- Diagnosis System
- Dtc Check / Clear
- Freeze Frame Data
- Fail-safe Chart
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Steering Angle Sensor Initialization Incomplete (C1439/31,C1445/31)
- Performance Decline of Brake Function (C1441)
- Yaw Rate Sensor Output Malfunction (C1448/98)
- Control Module Communication Bus OFF (U0073/94,U0100/65,U0123/62,U0124/95,U0126/63)
- Stop Light Control Relay Malfunction (C1380/64)
- Skid Control ECU Malfunction (C1300/62)
- Brake Pedal Load Sensing Switch (C1267/67)
- ECU Version Miss Match (C1288/88)
- Open in Stop Light Switch Circuit (C1249/49)
- Master Cylinder Pressure Sensor Malfunction (C1246/46,C1281/81)
- Speed Sensor Rotor Faulty (C1237/37,C1275/75-C1278/78)
- Low Battery Positive Voltage or Abnormally High Battery Positive Voltage (C1241/41)
- Steering Angle Sensor Circuit Malfunction (C1231/31)
- Malfunction in Deceleration Sensor (C0365/28,C1234/34,C1245/32,C1245/45)
- Engine Control System Malfunction (C1201/51)
- Open or Short Circuit in ABS Solenoid Relay Circuit (C0278/11)
- Open or Short Circuit in ABS Motor Relay Circuit (C0273/13)
- SFR Solenoid Circuit (C0226/21,C0236/22,C0246/23,C0256/24,C1225/25-C1228/28)
- ABS Control System Malfunction (43)
- Rear Speed Sensor RH Circuit (C0210/33,C0215/34,C1273/73,C1274/74,C1332/38,C1333/39)
- Front Speed Sensor RH Circuit (C0200/31,C0205/32,C1271/71,C1272/72,C1330/35,C1331/36)
- ABS Warning Light Remains ON
- ABS Warning Light does not Come ON
- Brake Warning Light Remains ON
- Brake Warning Light does not Come ON
- TRAC OFF Indicator Light Remains ON
- TRAC OFF Indicator Light does not Come ON
- VSC OFF Indicator Light Remains ON
- VSC OFF Indicator Light does not Come ON
- Slip Indicator Light does not Come ON
- Slip Indicator Light Remains ON
- TC and CG Terminal Circuit
- TS and CG Terminal Circuit
- Vsc Off Switch
- Yaw Rate And Acceleration Sensor
Rear Brake Flexible Hose
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
CAUTION / NOTICE / HINT
NOTICE:
If both the left and right side hoses are removed at the same time, be sure to
place identification ma ...
Brake Actuator
...
Other materials about Toyota Venza:
Removal
REMOVAL
PROCEDURE
1. DRAIN DIFFERENTIAL OIL
(a) Using a 10 mm hexagon wrench, remove the rear differential carrier
cover plug and gasket.
(b) Using a 10 mm hexagon wrench, remove the ...
Check For Intermittent Problems
CHECK FOR INTERMITTENT PROBLEMS
HINT:
Inspect the ECM using check mode. Intermittent problems are easier to detect
with the Techstream when the ECM is in check mode. In check mode, the ECM uses 1
trip detection logic, which is more sensitive to malfuncti ...
Reassembly
REASSEMBLY
CAUTION / NOTICE / HINT
HINT:
Use high-temperature grease to lubricate the bearings, gears and return spring
when assembling the starter.
PROCEDURE
1. INSTALL PLANETARY GEAR
(a) Apply grease to the planetary gears and pin parts of ...
0.1557