Toyota Venza: Bleeding

Toyota Venza Service Manual / Brake System (other) / Brake Fluid / Bleeding

BLEEDING

CAUTION / NOTICE / HINT

NOTICE:

Do not allow brake fluid to adhere to any painted surface such as the vehicle body. If brake fluid leaks onto any painted surface, immediately wash it off.
Before bleeding the brake system, confirm that the reservoir located above the master cylinder assembly is filled with brake fluid.
If bleeding is performed with the engine running or the engine switch on (IG), DTC C1441 will be stored. Make sure to clear the DTCs when work is complete.

HINT:

If any component of the brake system is removed and reinstalled, or if air in the brake lines is suspected, bleed the brake system.

PROCEDURE

1. FILL RESERVOIR WITH BRAKE FLUID

2. BLEED BRAKE MASTER CYLINDER

NOTICE:

To prevent brake fluid from damaging painted surfaces, cover any surrounding parts with a piece of cloth.
Be sure to clean your hands before bleeding from master cylinder to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problem.

HINT:

If the master cylinder is reinstalled or runs out of brake fluid, bleed the master cylinder.

(a) Using a union nut wrench, disconnect the 2 brake tubes from the brake master cylinder assembly.

(b) Slowly depress the brake pedal and hold it down.

(d) Uncover the holes, slowly depress the brake pedal and hold it down. While holding down the brake pedal, cover the tube holes again. Repeat this step 3 or 4 times.

(e) Using a union nut wrench, connect the 2 brake tubes to the brake master cylinder assembly.

Text in Illustration

*a	Torque Wrench Fulcrum Length

Torque:

Specified Tightening Torque :

20 N·m {199 kgf·cm, 14 ft·lbf}

NOTICE:

Do not bend or damage the brake lines.
Do not allow brake line to twist and interfere with other parts or body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake line.

HINT:

Calculate the torque wrench reading when changing the fulcrum length for the torque wrench (See page ).

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 250 mm (9.84 in.)):
18 N*m (184 kgf*cm, 13 ft.*lbf)

3. BLEED BRAKE LINE

4. INSPECT FOR BRAKE FLUID LEAK

5. INSPECT FLUID LEVEL IN RESERVOIR

6. CHECK AND CLEAR DTC

(See page )

Replacement

REPLACEMENT CAUTION / NOTICE / HINT NOTICE: Move the shift lever to P and apply the parking brake before bleeding the brakes. Add brake fluid to keep the level between the MIN and M ...

Brake Line

Precaution PRECAUTION 1. TROUBLESHOOTING PRECAUTION NOTICE: Since the brake lines are critical safety related parts, be sure to disassemble and inspect the components if a brake flui ...

Other materials about Toyota Venza:

Portable Player cannot be Registered
CAUTION / NOTICE / HINT HINT: Some versions of "Bluetooth" compatible audio players may not function properly, or the functions may be limited using the navigation receiver assembly, even if the portable audio player itself can play files (See ...

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (a) Inspect the shift lock operation. (1) Move the shift lever to P. (2) Turn the ignition switch off. (3) Check that the shift lever cannot be moved from P to any other position ...

Replacement
REPLACEMENT PROCEDURE 1. REPLACE INTAKE VALVE GUIDE BUSH (a) Heat the cylinder head to approximately 80 to 100°C (176 to 212°F). (b) Place the cylinder head on wooden blocks. (c) Using SST and a hammer, tap out the valve guide bush. SST: 0 ...