Toyota Venza: Back Door Support

Toyota Venza Service Manual / Door / Hatch / Back Door Support

Components

COMPONENTS

ILLUSTRATION

Removal

REMOVAL

PROCEDURE

1. REMOVE BACK DOOR STAY ASSEMBLY

NOTICE:

Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.
Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.
Do not apply any horizontal load to the door stay in order to prevent the piston rod from deforming.

(a) Using a screwdriver, remove the stop ring along the groove.

HINT:

Tape the screwdriver tip before use.

Text in Illustration

*1	Protective Tape

(b) Release the ball joint and remove the back door stay assembly.

NOTICE:

Remove the back door stay assembly while supporting the back door by hand.

2. REMOVE BACK DOOR LOWER DAMPER STAY BRACKET

(a) Remove the 2 bolts and back door lower damper stay bracket.

3. REMOVE BACK DOOR UPPER DAMPER STAY BRACKET

(a) Remove the 2 bolts and back door upper damper stay bracket.

Disposal

DISPOSAL

PROCEDURE

1. DISPOSE OF BACK DOOR STAY ASSEMBLY

(a) Secure the back door stay assembly horizontally in a vise with the piston rod pulled out.

(b) Wear safety glasses. Use a metal saw to slowly cut a groove between A and B shown in the illustration to release the gas.

Standard Dimension:

80.0 mm (3.150 in.)

NOTICE:

Although the gas inside the back door stay assembly is colorless, odorless and harmless, metal debris may scatter. Therefore, cover the back door stay assembly with a piece of cloth or other material.

Installation

INSTALLATION

PROCEDURE

1. INSTALL BACK DOOR UPPER DAMPER STAY BRACKET

(a) Clean the threaded portion on the vehicle body with a non-residue solvent.

(b) Apply adhesive to the threads of the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

2. INSTALL BACK DOOR LOWER DAMPER STAY BRACKET

(a) Clean the threaded portion on the vehicle body with a non-residue solvent.

(b) Apply adhesive to the threads of the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

3. INSTALL BACK DOOR STAY ASSEMBLY

NOTICE:

Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.
Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.
Do not apply any horizontal load to the door stay in order to prevent the rod from deforming.

(a) When reusing the back door stay assembly:

(1) Install the 2 stop rings to the back door stay assembly.

(b) Install the back door stay assembly.

NOTICE:

Install the back door stay assembly while supporting the back door by hand.

(c) Check that the back door stay assembly is engaged in the ball joint and that the back door stay assembly cannot be pulled out.

Back Door Opener Switch

Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE BACK DOOR PANEL TRIM ASSEMBLY 2. REMOVE REAR LIGHT ASSEMBLY LH 3. REMOVE REAR LIGHT ASSEMBLY RH HINT: Use t ...

Front Door

...

Other materials about Toyota Venza:

Installation
INSTALLATION PROCEDURE 1. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH (a) Temporarily install the rear No. 1 suspension arm assembly LH to the rear suspension member with the bolt (B). Text in Illustration ...

Inspection
INSPECTION PROCEDURE 1. INSPECT STEERING PAD SWITCH ASSEMBLY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition ...

Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) (P0016,P0017)
DESCRIPTION In the VVT (Variable Valve Timing) system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and ...