DESCRIPTION
The power back door ECU (power back door motor unit)*1 or back door closer ECU (multiplex network door ECU)*2 receives signals from the latch switch, sector switch and back door courtesy switch, which are built into the back door lock. Based on these switch signals, the latch position of the back door lock is determined.
DTC No. |
DTC Detection Condition |
Trouble Area |
---|---|---|
B2250 |
While the back door closer is operating, a malfunction is detected in position information from the sector switch within a specified amount of time. |
|
WIRING DIAGRAM
PROCEDURE
1. |
INSPECT BACK DOOR LOCK ASSEMBLY (SECTOR SWITCH) |
(a) Remove the back door lock assembly (See page ).
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Sector Switch
Tester Connection |
Condition |
Specified Condition |
---|---|---|
6 (DLSW) - 4 (E) |
Sector gear in neutral position (Sector switch on) |
Below 1 Ω |
6 (DLSW) - 4 (E) |
Sector gear not in neutral position (Sector switch off) |
10 kΩ or higher |
*1 |
Component without harness connected (Back Door Lock Assembly) |
*3 |
Sector Gear |
*2 |
Sector Switch |
- |
- |
NG |
REPLACE BACK DOOR LOCK ASSEMBLY |
|
2. |
CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU OR BACK DOOR CLOSER ECU) |
(a) w/ Power Back Door System
(1) Disconnect the R1 back door lock assembly connector and L20 power back door ECU connector.
(2) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
R1-6 (DLSW) - L20-24 (POS) |
Always |
Below 1 Ω |
R1-4 (E) - Body ground |
Always |
Below 1 Ω |
R1-6 (DLSW) - Body ground |
Always |
10 kΩ or higher |
*1 |
Front view of wire harness connector (to Back Door Lock) |
*2 |
Front view of wire harness connector (to Power Back Door ECU) |
(b) w/o Power Back Door System (1) Disconnect the R1 back door lock assembly connector and L21 back door closer ECU connector. (2) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
Result |
Proceed to |
---|---|
NG |
A |
OK (w/ Power Back Door System) |
B |
OK (w/o Power Back Door System) |
C |
A |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
B |
REPLACE POWER BACK DOOR ECU (POWER BACK DOOR MOTOR UNIT) |
C |
REPLACE BACK DOOR CLOSER ECU (MULTIPLEX NETWORK DOOR ECU) |
Control Module Communication Bus OFF (U0073/94,U0100/65,U0123/62,U0124/95,U0126/63)
DESCRIPTION
The skid control ECU receives the signals from the ECM, steering angle sensor,
and yaw rate and acceleration sensor via the CAN communication system.
DTC Code
DTC Detection Condition
Trouble Area
...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the engine immobiliser system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...
Disassembly
DISASSEMBLY
CAUTION / NOTICE / HINT
NOTICE:
When disassembling the multiplex network door ECU, eliminate static electricity
by touching the vehicle body to prevent the components from being damaged.
PROCEDURE
1. REMOVE MULTIPLEX NETWORK DOOR ECU
...