ADJUSTMENT
CAUTION / NOTICE / HINT
CAUTION:
Before adjusting the door positions of vehicles equipped with side and curtain shield airbags, be sure to disconnect the battery. After adjustment, check that the SRS warning light is operating normally and there are no SRS DTCs output.
HINT:
PROCEDURE
1. INSPECT FRONT DOOR
(a) Check that the clearance measurements of areas *1 through *23 are within each standard range.
Standard Clearance
Area |
Measurement |
Area |
Measurement |
---|---|---|---|
*1 |
3.0 to 7.0 mm (0.118 to 0.276 in.) |
*13 |
3.0 to 6.0 mm (0.118 to 0.236 in.) |
*2 |
-1.0 to 3.0 mm (-0.0394 to 0.118 in.) |
*14 |
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
*3 |
3.5 to 6.5 mm (0.138 to 0.256 in.) |
*15 |
3.2 to 7.2 mm (0.126 to 0.283 in.) |
*4 |
0.3 to 3.3 mm (0.0118 to 0.130 in.) |
*16 |
-2.0 to 2.0 mm (-0.0787 to 0.0787 in.) |
*5 |
3.5 to 6.5 mm (0.138 to 0.256 in.) |
*17 |
9.3 to 13.3 mm (0.366 to 0.524 in.) |
*6 |
1.3 to 4.3 mm (0.0511 to 0.169 in.) |
*18 |
3.2 to 7.2 mm (0.126 to 0.283 in.) |
*7 |
3.5 to 6.5 mm (0.138 to 0.256 in.) |
*19 |
-2.0 to 2.0 mm (-0.0787 to 0.0787 in.) |
*8 |
1.2 to 4.2 mm (0.0472 to 0.165 in.) |
*20 |
3.0 to 6.0 mm (0.118 to 0.236 in.) |
*9 |
3.5 to 6.5 mm (0.138 to 0.256 in.) |
*21 |
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
*10 |
0.6 to 3.6 mm (0.0236 to 0.141 in.) |
*22 |
3.0 to 6.0 mm (0.118 to 0.236 in.) |
*11 |
2.5 to 6.5 mm (0.0984 to 0.256 in.) |
*23 |
-1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
*12 |
-2.0 to 2.0 mm (-0.0787 to 0.0787 in.) |
- |
- |
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system (See page ).
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).
3. ADJUST FRONT DOOR
(a) Using SST, loosen the hinge bolts on the vehicle body and adjust the door position. SST: 09812-00010 |
|
(b) Tighten the hinge bolts on the vehicle body after the adjustment.
Torque:
26 N·m {265 kgf·cm, 19 ft·lbf}
(c) Loosen the hinge bolts on the door and adjust the door position.
(d) Tighten the hinge bolts on the door after the adjustment.
Torque:
26 N·m {265 kgf·cm, 19 ft·lbf}
(e) Using a T40 "TORX" socket wrench, slightly loosen the striker mounting screws. |
|
(f) Using a brass bar and a hammer, hit the striker to adjust its position.
(g) Using a T40 "TORX" socket wrench, tighten the striker mounting screws after the adjustment.
Torque:
23 N·m {235 kgf·cm, 17 ft·lbf}
4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).
5. INSPECT SRS WARNING LIGHT
(See page )
Precaution
PRECAUTION
NOTICE:
When disconnecting the cable from the negative (-) battery terminal, initialize
the following systems after the cable is reconnected.
System Name
See Procedure
Back Door Closer System
...
Throttle / Pedal Position Sensor / Switch "D" Circuit (P2120,P2122,P2123,P2125,P2127,P2128,P2138)
DESCRIPTION
HINT:
This Electronic Throttle Control System (ETCS) does not use a throttle
cable.
These DTCs relate to the accelerator pedal sensor assembly.
The accelerator pedal sensor assembly is mounted on the accelerator pedal brack ...
Terminals Of Ecu
TERMINALS OF ECU
NOTICE:
Turn the ignition switch off before measuring the resistances between
CAN bus main wires and between CAN bus branch wires.
Turn the ignition switch off before inspecting CAN bus wires for a ground
short.
After ...