Toyota Venza manuals

Toyota Venza: Installation

INSTALLATION

PROCEDURE

1. INSTALL REAR DOOR COURTESY LIGHT SWITCH

(a) Using "TORX" socket wrench T30, install the rear door courtesy light switch with the "TORX" bolt.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}


(b) Connect the rear door courtesy light switch connector.

2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)


3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)


4. CONNECT REAR SEAT OUTER BELT ASSEMBLY


5. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY


6. INSTALL RECLINING REMOTE CONTROL BEZEL


7. INSTALL REAR SEAT ASSEMBLY LH (for LH Side)


8. CONNECT REAR SEAT NO. 2 RECLINING CONTROL CABLE SUB-ASSEMBLY (for LH Side)


9. INSTALL REAR SEAT OUTER TRACK BRACKET COVER (for LH Side)


10. INSTALL REAR SEAT INNER TRACK BRACKET COVER (for LH Side)


11. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)


12. INSTALL REAR SEAT ASSEMBLY RH (for RH Side)


13. CONNECT REAR SEAT RECLINING CONTROL CABLE SUB-ASSEMBLY (for RH Side)


14. INSTALL REAR SEAT OUTER TRACK BRACKET COVER (for RH Side)


15. INSTALL REAR SEAT INNER TRACK BRACKET COVER (for RH Side)


16. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (for RH Side)


17. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)


18. INSTALL REAR FLOOR FINISH PLATE


19. INSTALL REAR SEAT SUB FLOOR PANEL ASSEMBLY


20. INSTALL NO. 1 DECK BOARD


21. INSTALL DECK SIDE TRIM BOX LH


22. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


23. INSTALL DECK SIDE TRIM BOX RH


24. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


25. INSTALL DECK BOARD ASSEMBLY


26. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


27. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


28. INSTALL REAR DOOR SCUFF PLATE


Inspection
INSPECTION PROCEDURE 1. INSPECT COURTESY LIGHT SWITCH (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Swit ...

Relay
On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT DOME CUT RELAY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: ...

Other materials about Toyota Venza:

Dtc Check / Clear
DTC CHECK / CLEAR 1. DTC CHECK/CLEAR (When Using the Techstream) (a) Check for DTCs. (1) Connect the Techstream to the DLC3. (2) Turn the ignition switch to ON. (3) Turn the Techstream on. (4) Read the DTCs following the prompts on the Techstream. Enter ...

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful bec ...

Dtc Check / Clear
DTC CHECK / CLEAR 1. CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Cruise Control / DTC. (e) Check the details of the DTC(s) (See page ). 2 ...

© 2016-2021 Copyright www.tovenza.com

0.2251