Toyota Venza: Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)

Toyota Venza Service Manual / Audio / Video / Audio And Visual System / Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)

DESCRIPTION

This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the audio and visual system vehicle customization screen.

HINT:

The certification ECU (smart key ECU assembly) controls the smart key system related items that are customizable via the audio and visual system vehicle customization screen.

DTC No.	DTC Detection Condition	Trouble Area
B15F7	Certification ECU (smart key ECU assembly) vehicle setting processing malfunction	CAN communication system Smart key system (for Entry Function) Smart key system (for Start Function) Certification ECU (smart key ECU assembly) Radio and display receiver assembly

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Registration (See page ).

PROCEDURE

1.	CHECK CAN COMMUNICATION SYSTEM

(a) Use the Techstream to check if the CAN communication system is functioning normally (See page ).

OK:

CAN communication DTCs are not output.

GO TO CAN COMMUNICATION SYSTEM

2.	CHECK SMART KEY SYSTEM (for Entry Function)

(a) Check if the smart key system (for Entry Function) is malfunctioning (See page ).

HINT:

Customization may not be possible depending on the malfunction in the smart key system (for Entry Function).

OK:

No malfunctions are present in the smart key system (for Entry Function).

GO TO SMART KEY SYSTEM (for Entry Function)

3.	CHECK SMART KEY SYSTEM (for Start Function)

(a) Check if the smart key system (for Start Function) is malfunctioning (See page ).

HINT:

Customization may not be possible depending on the malfunction in the smart key system (for Start Function).

OK:

No malfunctions are present in the smart key system (for Start Function).

GO TO SMART KEY SYSTEM (for Start Function)

4.	CHECK CUSTOMIZE ITEMS

(a) Make a note of the customizable items for each certification ECU (smart key ECU assembly) related system.

HINT:

The items shown as customizable via the audio and visual system vehicle customization screen can also be changed manually. In the following step, change the items manually.

(1) Check the customize parameters list for the smart key system (for Entry Function) related items that can be customized via the audio and visual system vehicle customization screen (See page ).

(2) Check the customize parameters list for the smart key system (for Start Function) related items that can be customized via the audio and visual system vehicle customization screen (See page ).

(b) Confirm that it is possible to manually change the settings of the customize parameters for each system that are available for customization via the audio and visual system vehicle customization screen.

OK:

The items available for customization via the audio and visual system vehicle customization screen can be customized successfully using the manual procedure.

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

XM Tuner Antenna Disconnected (B15FE,B15FF)

DESCRIPTION These DTCs are stored when a malfunction occurs in the roof antenna assembly which is connected to the stereo component tuner assembly. DTC No. DTC Detection Cond ...

A/C ECU Vehicle Information Reading/Writing Processor Malfunction (B15F5)

DESCRIPTION This DTC is stored when items controlled by the air conditioning amplifier assembly cannot be customized via the audio and visual system vehicle customization screen. HINT: The air co ...

Other materials about Toyota Venza:

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART HINT: If a trouble code is displayed during the DTC check, inspect the trouble areas listed below for that code. For details of the code, refer to the following "See page". Power back door system DTC C ...

Crankshaft Position Sensor "A" Circuit (P0335,P0339)
DESCRIPTION The crankshaft position sensor system consists of a crank angle sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The senso ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY) (a) Disconnect the 2A and 2F main body ECU (driver side junction block assembly) connectors. (b) Measure the voltage and resistance according to the value(s) in the table be ...